Programmeur clé Xtool
Program Smart Key for Renault Scenic III 2015 with Lonsdor K518ISE
Article publi le 18/08/2018
New test feedback: Lonsdor K518ISE Renault Scenic year 2015 smart key card programming success.
lonsdor-k518ise-renault-scenic-1
Select Immobilizer->Renault->Select from vehicle->Megane Scenic-> Scenic III (2009-2015)
lonsdor-k518ise-renault-scenic-2
Turn ignition to ON position
Read VIN, detect key number and ID
lonsdor-k518ise-renault-scenic-3
lonsdor-k518ise-renault-scenic-4
lonsdor-k518ise-renault-scenic-5
Insert original key card into key slot
lonsdor-k518ise-renault-scenic-6
Follow system prompt to program key
lonsdor-k518ise-renault-scenic-7
lonsdor-k518ise-renault-scenic-8
Program next key.
Insert new key card into slot and follow Lonsdor K518ISE prompts
lonsdor-k518ise-renault-scenic-9
Success.
Test the new smart key.
lonsdor-k518ise-renault-scenic-10
Done.


http://www.lonsdor.org/lonsdor-k518ise-program-renault-scenic-iii-2015-smart-card/
Aucun commentaire - Voir / Ajouter

How to use Eucleia TabScan to reset Volvo XC60 2011 EPB
Article publi le 17/08/2018
Vehicle Information: VOLVO XC60 year 2011


Example: EPB Reset after replacing rear brake block

Step 1: Turn on the ignition switch, select P gear, press the EPB switch to release the handbrake.
tabscan-volvo-xc60-epb-1

Select P gear and release the handbrake


Step 2:  Connect EUCLEIA Tabscan S7W/Tabscan S8 diagnostic scanner with vehicle
Select Service function
tabscan-volvo-xc60-epb-2

Step 3: Choose “EPB Reset”
tabscan-volvo-xc60-epb-3

Step 4: Choose “VOLVO”
tabscan-volvo-xc60-epb-4

Step 5: Choose“XC60”
tabscan-volvo-xc60-epb-5

Step 6: Choose “Replace the rear brake pads”
tabscan-volvo-xc60-epb-6

Step 7: Turn ignition on and engine off, click OK
tabscan-volvo-xc60-epb-7

Step 8: at this point, the brake pump will be retracted, and then the ring of rear wheel brake pump will be heard for a few seconds, waiting for the page to jump before replacing the new brake pad to the car.
tabscan-volvo-xc60-epb-8
tabscan-volvo-xc60-epb-9

Step 9. After the replacement is completed, click "confirm" and the brake pump will be released, and the ring of motor will be heard for a few seconds, waiting for the page to jump and then click "confirm".
tabscan-volvo-xc60-epb-10
tabscan-volvo-xc60-epb-11

Step 10: Click “OK” button and exit the system. Turn off and then turn on the ignition switch and press EPB button. Completed.
tabscan-volvo-xc60-epb-12

Note:

For EPB Reset usually need release the handbrake.


http://tabscan.blogspot.com/2018/08/eucleia-tabscan-reset-epb-on-volvo-xc60-2011.html 
 
 
Aucun commentaire - Voir / Ajouter

How to Send Diagnostic Feedback to Launch X431 company
Article publi le 15/08/2018
How to send diagnostic feedback to Launch X431 engineer?


Part 1:  How to Diagnose 

Step 1:

After connect DBS connector to car, and log in X431 App

Stay in the main page , the set the ignition switch to ON

Click Local Diagnose
launch-x431-send-diagnostic-feedback-1

Step 2: 

After enter Local Diagnose, we need to choose the diagnose software.

There are 3 methods to choose software, Camera Scan/Enter VIN/Manual Select
launch-x431-send-diagnostic-feedback-2

1. Scan VIN of the car by Camera Scan, and it will choose software automaticaaly 

2. Input IN of the car manually, and it will enter software automatically

3. Select software manually
launch-x431-send-diagnostic-feedback-3
launch-x431-send-diagnostic-feedback-4
Note: If there is no macthing software, please download it in Software Update function
launch-x431-send-diagnostic-feedback-5
Step 3:
Search Bluetooth. Connect DBScar connector with diagnose device, or for some devices, you can connect them together with USB cable
launch-x431-send-diagnostic-feedback-6
launch-x431-send-diagnostic-feedback-7
launch-x431-send-diagnostic-feedback-8
Health Report: Do a comprehensive scan and generate an all-system report
System Scan: Show all equipped system

Step 4:
Choose System Selection 
launch-x431-send-diagnostic-feedback-9

Step 5:
Choose the module or system that you want to diagnose
launch-x431-send-diagnostic-feedback-10
You can do following through these procedure:
Read fault code, clear fault code, read data stream, do actuation test, and some special functions or programming in some module or system


Part 2: Send Diagnostic Feedback

You can upload the diagnostic records to Launch professional engineer when you are faced with problems during the operation. 

Step 1:
launch-x431-send-diagnostic-feedback-11
Back to main page of X431 App and click Feedback
launch-x431-send-diagnostic-feedback-12
Step 2:
After enter feedback, you can find the latest 20 diagnostic records on this page
launch-x431-send-diagnostic-feedback-13

launch-x431-send-diagnostic-feedback-14
Step 3:
Choose the Launch X431 record which has problems and submit it with a detailed problem description your contact  information and even some pictures
launch-x431-send-diagnostic-feedback-15

History: shows the feedback process, done, in progress, or pending 
launch-x431-send-diagnostic-feedback-16

Offline-list: Shows the failed upload feedbacks, please choose re-upload
launch-x431-send-diagnostic-feedback-17
Launch X-431 engineer will see your feedback in the backstage and try their best to help you as soon as possible.

Aucun commentaire - Voir / Ajouter

Benz Sprinter 2010 EZS Soldering Pinouts to Xprog and R270
Article publi le 14/08/2018
Purpose: 
Do odometer correction on 2010 Sprinter Van. I need the soldering points for the ezs/eis.I can't actually see the mask but after extensive reading every points to them having the 0L01Y mask. Which programmer will work?



Solution:

R260 original ok
clone rosfar,ok
xprog clone ok
R270 ok


Use xprog the pinouts for xprog is what posted below. i always do this with xprog and never had a problem just select in device options " read and verify " make sure it is NOT selected and you should be ok , use the BDM adaptor with xprog for it
here is the settings i use and you know the story always keep backup of the files you read

xprog-sprinter-ezs-1



xprog-sprinter-ezs-2



xprog-sprinter-ezs-3

BTW:


Here are R270 wires:

2- +5v

24,26- ground

7- reset

19- background

r270-sprinter-ezs-1


http://xprogbox.blogspot.com/2018/08/benz-sprinter-2010-ezs-pinout-to-xprog.html 
 
Aucun commentaire - Voir / Ajouter

BMW F series Airbag MAC7241 Resetting using Xprog
Article publi le 13/08/2018
How to use Xprog m box ecu programmer to read BMW F series Airbag?

Check pinouts below:
xprog-bmw-f-series-airbag-MAC7241-1

xprog-bmw-f-series-airbag-MAC7241-2

xprog-bmw-f-series-airbag-MAC7241-3

xprog-bmw-f-series-airbag-MAC7241-4

xprog-bmw-f-series-airbag-MAC7241-5
http://www.obdii365.com/producttags/xprog.html
Aucun commentaire - Voir / Ajouter


[ 1 ] [ 2 ] [ 3 ] [ 4 ] [ 5 ] [ 6 ]
Crez votre Blog !
Titre du blog :
Programmeur clé Xtool
Description :
Xtool obd outil de diagnostic de voiture, programmeur principal, service technique de scanner obd2.
Dernire mise jour :
18/08/2018
Accueil
Me contacter
Livre d'or
Articles sur ce blog : 28
Commentaires sur le blog : 0
Visites depuis la cration : 911
Visites depuis hier : 27